Dimensions Orifice Weld Neck RTJ flanges ASME B16.36 Class 1500


flanges

 
Class 1500 NPS 1-24

NPSOUT
SIDE
DIA
MIN
THK
FLG
HGT
FLG
GRV
NO
PITCH
DIA
GRV
DEPTH
OTHPE
115038.183R1650.806.35
18038.189R2068.276.35
221538.1102R2495.257.92
24541.3105R27107.957.92
326547.7117R35136.537.92
431054.0124R39161.937.92
639582.6171R46211.149.52
848592.1213R50269.8811.13
10585108.0254R54323.8511.13
12675123.9283R58381.0014.27
14750133.4298R63419.1015.88
16825146.1311R67469.9017.48
18915162.0327R71533.4017.48
20985177.8356R75584.2017.48
241170203.2406R79692.1520.62
NPSOTHGRV
NO
PE
OUT
SIDE
DIA
MIN
THK
FLG
HGT
FLG
PITCH
DIA
GRV
DEPTH


NPSGRV
WIDTH
R
BTM
HGT
OVAL
RING
HUB
DIA
HUB
DIA
DIA OF
TAP
FRWXATg
18.740.825.45233.56.4
8.740.825.47048.36.4
211.910.827.010560.36.4
11.910.827.012473.06.4
311.910.827.013388.99.5
411.910.827.0162114.312.7
613.491.528.6229168.312.7
816.661.533.3292219.112.7
1016.661.533.3368273.012.7
1223.011.539.7451323.812.7
1426.972.444.4495355.612.7
1630.182.450.8552406.412.7
1830.182.450.8597457.212.7
2033.322.454.0641508.012.7
2436.532.458.7762609.612.7
NPSFRWXATg
GRV
WIDTH
R
BTM
HGT
OVAL
RING
HUB
DIA
HUB
DIA
DIA OF
TAP


NPSBOLT
CIRCLE
NO OF
BOLTS
DIA OF
HOLES
DIA
STUD
BOLTS
STUD
BOLT
L
1101.6417/8160
123.841.1/81165
2165.1817/8165
190.581.1/81180
3203.281.1/8185
4241.381.3/8215
6317.5121.3/8280
8393.7121.3/41.5/8310
10482.61221.7/8355
12571.6162.1/82400
14635.0162 3/8445
16704.8162 5/8485
18774.7162 7/82.3/4535
20831.8163.1/83570
24990.6163.5/8660
NPSBOLT
CIRCLE
NO OF
BOLTS
DIA OF
HOLES
DIA
STUD
BOLTS
STUD
BOLT
L
 

 

General Notes:

  • Dimensions are in millimeters, except for bolts and bolt holes.
  • All other dimensions are in accordance with ASME B16.5.
  • Ring joint flanges larger than NPS 3 will require angular meter taps.

Notes:

  • Other NPT sizes may be furnished if required.
  • Bolt lengths for raised face flanges include allowance for orifice and gasket thickness of 6 mm (0.25 in.) for NPS 1 to NPS 12. Bolt lengths for ring-type joint flanges include allowance of 15 mm (0.62 in.) for NPS 1 to NPS 3.
  • Bore (B) is to be specified by the purchaser.
  • The length of the Stud Bolt does not include the height of the chamfers (points).

images

TOLERANCES

Tolerances on all dimensions shall be as shown in ASME B16.5 except for those shown below.

PRESSURE TAP LOCATION

Tolerance on location of center of pressure tap hole from flange face shall be:

  • ±0.5 mm (±0.02 in.) for flanges smaller than NPS 4
  • ±0.8 mm (±0.03 in.) for flanges NPS 4 and larger

BORE DIAMETER

Bore diameter tolerance (Welding Neck flanges only) is ±0.5% of nominal value.